215-876-7037
Mold Inspections & Testing Eastern PA

mold-inspection-company-eastern-pa

Certified Mold Inspection & Mold Testing Eastern PA

A thorough mold inspection is the starting point for any suspected mold-related issue. Without mold testing, there’s no way to accurately determine how bad your mold problem is – or if one exists at all. Your mold inspection will allow us to determine if you have mold, how bad it is, how to properly get rid of it and how to prevent it from returning. If you suspect you have mold in your home, basement, attic or commercial building, or are concerned about black mold or toxic mold, call MasterTech of Eastern PA today. 1 (215) 876-7037

We also offer indoor air quality assessments and will come take air samples to determine if your indoor mold spore levels are higher than they should be. If you are concerned with your indoor air quality, air testing will provide the necessary answers to your mold-related questions.

What to expect from your Mold Inspection:

01

Visual Inspection:

A thorough visual inspection is the starting point for every residential or commercial mold assessment. Your mold inspector will be looking for conditions that promote mold growth.

02

Digital Documentation:

Documenting our findings through digital imaging is the easiest way for your mold inspector to relay his or her findings. We’ll take pictures of all the areas of concern so you see exactly what we saw during your mold inspection.

03

Thermal Imaging:

Thermal imaging cameras (or infrared cameras) allow us to detect temperature differences in (and often behind) building materials. Why is this important? Because damp or wet building materials are almost always cooler than dry materials – and it’s the temperature difference that the infrared camera detects. It’s an invaluable tool in the detection of moisture sources that cause mold growth.

04

Moisture Mapping:

Since mold needs moisture to develop and thrive, finding that source of moisture is very important. Moisture mapping basically allows us to locate building materials that are damp or wet enough to support mold growth. Testing for moisture also helps us determine if water leaks have been resolved or if they are actively leaking and can locate where water damage starts and stops.

05

Airborne Mold Testing:

Your mold inspector may need to take air samples to determine if your indoor mold spore levels are higher than they should be.

06

Surface Mold Testing:

Is it just water staining, or is it mold? Surface testing with mold swabs or bio tape lifts will answer those questions. In many cases, surface testing isn’t necessary if mold growth is visibly obvious.

07

Inner Wall Mold Testing:

When mold is suspected behind a wall or above a ceiling, those areas should be tested. Today’s mold testing technologies and techniques allow mold inspectors to take air and surface samples from wall or ceiling voids without causing unnecessary damage to the property.

08

Mold Inspection Summary Report:

Within 48 hours after your home mold inspection, your inspector will compile all of his or her findings and generate an easy to understand mold inspection report.

09

Scope of Work:

If requested, your mold inspector will design a mold remediation plan specific to your property. Your scope of work will include cleanup suggestions as well as preventative measures that are necessary to keep mold from returning.

10

PRV Testing (Post Remediation Verification Testing):

Also referred to as clearance testing. This is a mold inspection after the remediation is complete. Since we’re removing a bio hazard, It’s important to know that the job was done right – the first time. PRV Testing will determine if cleanup efforts were successful or if further cleanup is necessary.

Mastertech Environmental is certified to perform mold inspections and mold testing thorough Eastern PA. If you are looking for the safest and most thorough assessment, then we are the company to help.

Call us today 1-215-876-7037

Your Mold Inspection Will Include:

A thorough visual inspection of the residential or commercial property (inside & out).

Digital documentation of our findings.

Thermal imaging (Infrared Camera Inspection) of potential problem areas.

Moisture mapping in areas where water intrusion may be a problem.

Indoor airborne mold testing to determine if mold levels are elevated inside your home or business.

Swab or bio tape mold samples to determine if mold is present on surfaces or belongings.

Inner wall testing to determine if mold is present in wall or ceiling voids.

A detailed report outlining what we did, what we found, where we found it and what to do next.

Need a Mold Inspection in your Eastern Pennsylvania Area?

Contact us

Contact us for help, additional info or assistance and we'll be with you in no time!


Enter your name

Enter your email

Enter your phone number

Your message